Mapping of the Sword
We will begin this section by texturing the sword. Before we launch into making the UV co-ordinates though it is necesary to think about how the materials we are going apply are made up.
For example here will have a single texture sheet but various other metal materials will be applied to different parts of
In the same way as the modelling we will work with the LPM and let the meshsmooth worry about the high poly version. This gives us far less polygons to set UV maps for.
In Max 4 it is better to work with polygons and not the usual mesh. This enables a better smoothing of the texture.
Apply a turn to poly modifier above the edit mesh and then right click it and select Collapse to.
The object is now an Editable Poly.
Note that one does not lose the meshsmooth settings for the creases and weights etc.
We will assign a separate material ID for each different part of the sword where a separate material will be used
Create a Multi-Sub/Object material.
By default Max Defines 10 Sub-Materials.
The ID 1 will be asigned to the parts of the sword whose UV were not yet defined, so it is easy to see what remains to
One can make Drag and Drop of the default blue material into Sub material 1.
One can also name this Sub MatÃ©riau, here default.
Finally give a name has this Multi-Sub/Object material, here Epee.
To assign this material to the sword, select when done and drag and drop the material slot on the object.
It may be that some faces of the object have a ID material different from 1, in this case, to clean the ID, select all model in Element mode, enter value 1 in material ID (Surface Properties roll out).
All the faces have now the ID 1
Create a material checker with Tile of 20 for example.
Then with Drag and Drop it with into ID 2 in Instance mode.
This material will use to adjust the UV of all the sword and it will be copied each time as an instance, one can thus easily change Tile for all with the original material
The ID 2 will be the material of the blade.
in polygon mode select all the faces of the blade
Enter Material ID value 2.
The selected faces change color, the checkerwork does not appear because UV are not defined. (do not forget to activate the posting of textures in the material checkerwork).
Always in sub-object mode with the faces selected in Editable Mesh, apply a planar UVW Map
For direct Gizmo of mapping correctly, use View Align in View Face, Center and the FIT to fix it on the selection of
Finally the board of texture will be square with equal values in Length and Width.
Here you do not need to improve UV.
In the stack, right click on the UVW Map, and select Collapse To to simplify it.
Thus helps with memory speed.
Meshsmooth remains on top and one does not lose the adjustments on Creases or Weights.
Return to Editable Poly in Polygon mode, benefit from the still active selection to hide the faces already textured with Hide.
By making this operation after each UVW Map, it becomes increasingly simple to select the not yet textured faces.
In Material Editor, copy the checker into ID 3
Select the corresponding faces as shown then apply Material ID 3.
As previously, apply to these faces a planar UVW Map, then enter the same values in Width and Length to have a coherent mapping with that of the blade, proceed as before.
select the faces opposite and apply the checker ID 4.
Another planar UVW then 'collapse to' the stack
Click on Meshsmooth, you can see that the higher density mesh still maintains the correct mapping
To still improve one thing, activate Materials in Surface Parameters, that smooths according to materials.
There are thus clearer and better smoothed material limits.
As before, click on UVW Map and Collapse To.
Note that one you can temporarily suspend the effect of a modifier while clicking on the icon bulb next to it.
Select the faces opposite.
Create matÃ©rial ID 5, assign to these faces then apply a planar UVW map.
Always give same dimension to the Gizmo when mapping.
Make in the same way material ID 6
This part is the most complex to map correctly, for the moment one is satisfied to apply a planar map to these faces
The adjustment will be made once all faces have the checker material
The ID 7 and 8 are for the central decoration of the guard.
Select the corresponding faces, external with ID 7 and interior faces with ID 8.
Apply planar UVW again
For the handle, ID 9 and mapping cylindrical.
With the Gizmo of mapping a rotation of 90° on the axis of Z so that the seam falls in line with the one on the handle.
Same proceedure for the rings, with cylindrical ID 10, mapping and rotation of Gizmo.
Arrived at this stage all the slots of Sub Materials are used.
To add some click on Add.
The pommel with the ID 11 and always a cylindrical mapping and the rotation of Gizmo.
Finally to finish with the ID 12, a planar map.
next page >